UNILIT 200-300 – 400 (ARENINO G – N - F)

 COLOURED FINISHING MORTARS

DESCRIPTION

UNILIT 200, 300 and 400 are traditional, dry premixed mineral and finishing mortars based on hydraulic, naturally pure and selected lime.

UNILIT 200, 300 and 400 are characterised by a high impact resistance and are resistant against atmosphere influences.

APPLICATION

UNILIT 200, 300 and 400 mortars are very vapour permeable and are completely compatible with the UNILIT system as finishing layers.  The optimum vapour permeability allows the moisture present in the wall to be able to rapidly migrate from the structure.

TECHNICAL PROPERTIES

Delivery form                                      powder

Density                                               1.560 kg/m³

Tensile strength : Unilit 300                   0,6 N/mm²

                          Unilit 400                   0,5 N/mm²

Compressive strength          

Unilit 300                                            10 N/mm² after 60 d

           12 N/mm² after 90 d

Unilit 400                                             5 N/mm² after 60 d

                                        6 N/mm² after 90 d

Modulus of elasticity                              6.130 N/ mm²

Coefficient of thermal conductivity         l = 0,30 W/m °K

Vapour diffusion resistance                      m = 10,4

pH value                                               > 10,5

Fire classification                                  non-flammable MO

Granular size : Unilit 200                        0 to 4 mm

   Unilit 300                        0 to 1.7 mm

                      Unilit 400                        0,7 mm

Proportion water/Unilit 300-400              0.16 l/kg

Mixing time                                           3 to 5 minutes

CONSUMPTION

Dependent upon the background and required layer thickness: 4 to 7 kg/m². 

Approx. 1,5 to 1,8 kg/m²/mm layer thickness.

Total layer thickness :  3 to 4 mm as finishing layer, applied in two layers (wet on wet). 

COLOUR

UNILIT 200, 300 and 400 are supplied in 12 colours.

PREPARATION

The substrate must be clean and free of all traces of oil and grease.  When the substrate has been treated with an impregnating product (silicone and similar) it is recommended to consult the supplier or manufacturer.

UNILIT 200, 300 and 400 are mixed with clean water.  Depending on the situation and substrate 4 to 5 litres of water are mixed with 25 kg of powder.  The mixing can be done either manually or mechanically, for 3 to 5 minutes.  The mortars can be applied directly to either dry or damp substrates.  If the substrate is too dry, dampen down the surface prior to overcoating.

UNILIT 200, 300 and 400 remain workable for 2 hours, in temperatures between 5°C and 40°C.  The drying period is 24 - 48 hours.  They have to be protected from frost for 48 - 72 hours after their application.

PACKING

30 kg bags

REMARKS

In case of doubt regarding the substrate, consult our technical service department. The material must be stored dry and frost free above ground. The maximum storage time is 6 months. Our advice and information is given in good faith and depending on the latest developments of our products. We guarantee the constant quality of our products, but do not accept any liability concerning the application.

!! The product may not come into contact with the surfaces below ground level, unless applied over UNILIT 30 !!

Arte Constructo bvba - Molenberglei 18 - B- 2627 Schelle (Belgium)

tel: +32 (0)3 880.73.73   fax: +32 (0)3 880.73.70

Info@arteconstructo.be

made by stevensschool